Planet NVR-1620 Guía de instalación

4/8/16/32-Ch Network Video RecorderNVR SeriesQuick Installation Guide

1014. Slide the side housing back to the unit.15. Secure the housing with the screws highlighted below.2.2 8/16-Ch Network Video Recorder2.2.1 NVR-81

112.2.2 NVR-810 / NVR-1610 Physical DetailsFront PanelNVR-1610IP CameraStatus LEDResetButtonPowerButtonBuzzerButtonUSB PortNVR Status LEDsNVR-1610Netw

12NetworkAmber Solid amber for activity on a 1Gbps networkGreen Solid green for activity on a 10/100Mbps networkStatusAmber Blinking during rmware up

13Connector DescriptionAC Connect the power cord to AC 100~240V power source.Ethernet Supports 10/100/1000Base-T interface.RS-232 Connect to UPS.I/O2.

143. Remove the screws on the left and right side of the HDD tray.HDDTray4. Insert the HDD in the HDD tray. Please push the HDD until the SATA connect

157. Connect the bundled power adapter to the power connector on rear panel.8. Press power button to power on your NVR.2.2.4 NVR-820 / NVR-1620 Packag

16Rear PanelLEDs Status DenitionsHDD x 2Green Solid green when the HDD is mountedRed Solid red for disk failAmberSolid amber when recording is in pro

17Buttons Status DenitionsPowerON Press and hold for 2 seconds OFF Press and hold for 2 secondsResetRestore defaultPress and hold for 5 secondsRestar

182. Place the HDD in the tray on the left. Slide it in until it is securely connected with the SATA connector.3. Secure the HDD with the tool-less

194. Place the top case and secure it with the screws on both sides.2.3 32-Ch Network Video Recorder2.3.1 NVR-3210 Package Contents1 x NVR 1 x Power

Table of ContentsChapter 1. Introduction ... 3 1.1 Before Installat

20LEDs Color DescriptionSystem AmberFirmware upgrade: blinkingSystem failure (AP fail): offSystem normal: solidEvent AmberEvent recording: solidNo eve

212.3.3 NVR-3210 HDD Installation1. Release the HDD tray by pulling the lock to the right.2. Pull the HDD tray out of the case.3. Place the HDD in the

224. Put the HDD tray back to the case.5. Push the tray door back to the case to secure it.2.3.4 NVR-3250 Package Contents1 x NVR 1 x Power Cord 1 x R

232.3.5 NVR-3250 Physical DetailsFront PanelHDD 1 HDD 2 HDD 3USB1 USB2EventLEDSystemLEDPowerLEDPowerButtonResetButtonHDD 4LEDs Color DescriptionPower

24Connector DescriptionVGA VGA outputEthernet 10/100/1000Mbps networkUSB Connect your USB ash disk for rmware upgrade and backupE-SATA External E-SA

253. Simply pull to remove the front plate once the screws are loosened from the unit.4. Remove the HDD tray by pulling the latch.5. Push

266. Once the tray is removed from the unit, notice there are four holes, which are used to secure the HDD.7. Once the HDD is placed in the tra

279. Secure the tray by pushing in the latch, which locks the tray with the unit.2.4 Web ManagementInstall “Device Search” utility from the CD1. Plea

283. Login the Homepage The Web management allows you to access and manage the Network Video Recorder easily. Launch the Web browser

3Chapter 1. IntroductionThank you for purchasing PLANET 4/8/16/32-Ch Network Video Recorder. The Network Video Recorder is designed for

4Chapter 2. Physical Description and Installation2.1 4-Ch Network Video Recorder2.1.1 NVR-420 Package Contents1 x NVR 1 x Power Cord 1 x Power Adapte

5HDD1/2Green Disk is onlineRed Disk errorAmberSolid amber when NVR-420 is recordingBlinking amber when the disk is recyclingOff No disk or disk is of

62. Use a Philips screw driver to release the screws.3. Slide open the case as shown below.4. One side of the housing can be detached as shown below.

75. Install the HDD by sliding its bottom rst into the tray diagonally to avoid the tray separator.6. Once the HDD is placed into the t

88. Make sure the screw holes on the HDD are aligned with the ones on the tray.9. Secure the HDD with the screws provided in the accessory box

911. Make sure the HDD is securely attached. 12. Place the HDD to the tray and make sure the screw holes on the HDD are aligned with the o